FW300R V6 刷openwrt 成功，但是无线不能用。

wlmwwx

我给你传了一个编程器读出来的固件，你再试试。以前那个我是用dd命令读出来的，应该是没问题的。

tangxin991

世道变了。。。 发表于 2013-3-17 08:28
我用编程器刷入UBOOT后就是半砖状态。四LAN口和WAN口灯亮一下就全灭了。插上网线灯亮但不分配IP。PING不通 ...

我的是6445的8兆rom，编程器刷uboot，然后可以出现uboot的web界面，别的没什么

tangxin991

固件有更新了吗，看日期好像是3月18号的，文件大小只有3.3兆了

wlmwwx

我下载了，无法升级，错误是can't open image file. 估计是没传完。

tangxin991

我下载了，web升级完毕重启，但是启动没反应，正在焊接ttl看到底怎么回事

tangxin991

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620
DRAM:  Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

______________________________________________________
|   ____                           ____              |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  <   |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                    |
|                 DreamBox Team                      |
|           http://www.openwrt.org.cn                |
|              Board:Mercury MW305R                  |
|                                                    |
|          lintel<lintel.huang@gmail.com>            |
|____________________________________________________|

===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44
============================================

GPIO Init:
        UARTF_SHARE_MODE:GPIO
        I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.

Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   PandoraBox Linux-3.3.8
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    921526 Bytes = 899.9 kB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:e0fb6
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


DreamBox Ralink Target. Copyright 2005-2012 Lintel<lintel.huang@gmail.com>


LINUX started...

THIS IS ASIC
[    0.000000] Linux version 3.3.8 (lintel@ZBT-Server) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #30 Mon Mar 18 16:38:41 CST 2013
[    0.000000] MediaTek MT7620 CPU:580MHz, Bus:145MHz Uart:40MHz
[    0.000000] Boot form:SPI FLASH
[    0.000000] MIPS CPU sleep mode enabled.
[    0.000000]  Detecting memory...64 MB!
[    0.000000]  PCIE: bypass PCIe DLL.
[    0.000000]  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[    0.000000]  disable all power about PCIe
[    0.000000]  PCIE: PLL power down for MT7620N
[    0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 board=MW305R rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61988k/65536k available (2190k kernel code, 3548k reserved, 366k data, 172k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] MTK/Ralink System Tick Counter init... cd:802701d0, m:214748, s:32
[    0.000000] console [ttyS1] enabled
[    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is Mercury MW305R
[    0.110000] Ralink Board GPIO_MODE init:
[    0.110000]  I2C:GPIO
[    0.120000]  SPI_REFCLK:GPIO
[    0.120000]  UART_F:GPIO
[    0.130000] GPIO_MODE_REGs: 0x1a311d
[    0.130000] General GPIO Driver for MediaTek MT7620 Board . 漏 2005-2012 lintel<lintel.huang@gmail.com>
[    0.140000] GPIO maped at address:0xb0000600.
[    0.140000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0
[    0.150000] GPIO maped at address:0xb0000600.
[    0.150000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1
[    0.160000] GPIO maped at address:0xb0000600.
[    0.160000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2
[    0.170000] GPIO maped at address:0xb0000600.
[    0.170000] gpiochip_add: registered GPIOs 72 to 95 on device: MT7620-GPIO3
[    0.180000] RALINK_GPIOMODE = 1a311d
[    0.180000] RALINK_GPIOMODE = 18311d
[    0.280000] PPLL_CFG1=0x4010000
[    0.290000] MT7620 PPLL unlock
[    0.300000] bio: create slab <bio-0> at 0
[    0.310000] Switching to clocksource Ralink external timer
[    0.320000] NET: Registered protocol family 2
[    0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.340000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.370000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.380000] TCP reno registered
[    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] NET: Registered protocol family 1
[    0.420000] Ralink GPIODEV resource maped.
[    0.430000] RT3xxx EHCI/OHCI init.
[    0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.460000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZO) (RTIME) (RUBIN) (CMODE_FAVOURLZO) (c) 2001-2006 Red Hat, Inc.
[    0.490000] msgmni has been set to 121
[    0.490000] io scheduler noop registered
[    0.500000] io scheduler deadline registered (default)
[    0.510000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.520000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[    0.540000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[    0.550000] Enable Ralink GDMA Controller Module
[    0.560000] GDMA IP Version=3
[    0.570000] spidrv_major = 217
[    0.590000] brd: module loaded
[    0.590000] deice id : c2 20 17 c2 20 (2017c220)
[    0.600000] MX25L6405D(c2 2017c220) (8192 Kbytes)
[    0.610000] mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
[    0.640000] Squashfs filesystem found at offset 0x150000,adjustment mtd partition.
[    0.650000] Creating 7 MTD partitions on "raspi":
[    0.660000] 0x000000000000-0x000000030000 : "U-Boot"
[    0.670000] 0x000000030000-0x000000040000 : "U-Boot-Env"
[    0.680000] 0x000000040000-0x000000050000 : "Factory"
[    0.700000] 0x000000050000-0x000000150000 : "kernel"
[    0.710000] 0x000000150000-0x000000800000 : "rootfs"
[    0.720000] mtd: partition "rootfs" set to be root filesystem
[    0.730000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=470000
[    0.750000] 0x000000390000-0x000000800000 : "rootfs_data"
[    0.760000] 0x000000050000-0x000000800000 : "linux"
[    0.770000] 0x000000000000-0x000000800000 : "fullflash"
[    0.780000] rdm_major = 253
[    0.790000] [debug] (ra_mtd_read_nm line: 268) Read EEPROM from mtd partition:Factory
[    0.800000] SMACCR1 -- : 0x0000000c
[    0.810000] SMACCR0 -- : 0x43762077
[    0.820000] Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
[    0.840000] [debug] (ra_mtd_read_nm line: 268) Read EEPROM from mtd partition:Factory
[    0.850000] SMACCR1 -- : 0x0000000c
[    0.860000] SMACCR0 -- : 0x43762077
[    0.870000] PROC INIT OK!
[    0.870000] Ralink APSoC Hardware Watchdog Timer
[    0.880000] TCP cubic registered
[    0.890000] NET: Registered protocol family 17
[    0.900000] 8021q: 802.1Q VLAN Support v1.8
[    0.910000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.920000] Freeing unused kernel memory: 172k freed

tangxin991

##### MediaTek MT76xx ESW VLAN Partition(WLLLL) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10002
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10001
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[    2.650000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    5.880000] CPU 0 Unable to handle kernel paging request at virtual address 00000020, epc == 80080b68, ra == 80080bf8
[    5.910000] Oops[#1]:
[    5.910000] Cpu 0
[    5.910000] $ 0   : 00000000 00000000 83a9ffe6 00000001
[    5.910000] $ 4   : 83801800 81076000 83b001f8 00001b0a
[    5.910000] $ 8   : 00000001 00001b09 83b000f0 00000001
[    5.910000] $12   : 77d98000 f0000000 00000001 0042aa44
[    5.910000] $16   : 83a9ffde 83a8c0e0 83a9fec8 83a9ff00
[    5.910000] $20   : 00000020 000000f8 802d0000 8023d520
[    5.910000] $24   : 00000120 77cc6be0                  
[    5.910000] $28   : 83ab2000 83ab3d88 00000001 80080bf8
[    5.910000] Hi    : 0000000c
[    5.910000] Lo    : 00000001
[    5.910000] epc   : 80080b68 0x80080b68
[    5.910000]     Tainted: G           O
[    5.910000] ra    : 80080bf8 0x80080bf8
[    5.910000] Status: 1100ff03    KERNEL EXL IE
[    5.910000] Cause : 00800008
[    5.910000] BadVA : 00000020
[    5.910000] PrId  : 00019650 (MIPS 24KEc)
[    5.910000] Modules linked in: leds_gpio button_hotplug(O) input_polldev input_core
[    5.910000] Process preinit (pid: 431, threadinfo=83ab2000, task=83ae58f0, tls=77db3440)
[    5.910000] Stack : 7fed3000 83a9fdc0 834166d4 8007b87c 83a9fec8 83a9f268 83a9f9a0 77cbc000
[    5.910000]         83ab3e1c 00000000 00000000 00400000 00000000 8007611c 83a9f688 83b03300
[    5.910000]         7fff7fff 00000000 77cbc000 80066e0c 83ad3d68 83ad3d68 83b03300 7fff8000
[    5.910000]         83b03334 8026c630 00000000 00000001 00000000 8007c848 00989680 83abe000
[    5.910000]         00000000 ffffffff 83ab3e18 00000000 00000062 83b03300 83b03303 00000001
[    5.910000]         ...
[    5.910000] Call Trace:[<8007b87c>] 0x8007b87c
[    5.910000] [<8007611c>] 0x8007611c
[    5.910000] [<80066e0c>] 0x80066e0c
[    5.910000] [<8007c848>] 0x8007c848
[    5.910000] [<8001bc1c>] 0x8001bc1c
[    5.910000] [<80020314>] 0x80020314
[    5.910000] [<800216d4>] 0x800216d4
[    5.910000] [<80021b14>] 0x80021b14
[    5.910000] [<80022550>] 0x80022550
[    5.910000] [<80022274>] 0x80022274
[    5.910000] [<800222b4>] 0x800222b4
[    5.910000] [<8000b024>] 0x8000b024
[    5.910000]
[    5.910000]
[    5.910000] Code: 26f7d520  08020302  241e0001 <8e930000> 5271000d  8e020014  12200008  92c243b8  38420001
[    6.290000] ---[ end trace c4b55eee587dd6a2 ]---
[    6.300000] Fixing recursive fault but reboot is needed!

tangxin991

上面报错了， Warning - bad CRC, using default environment
难道文件有问题？

wlmwwx

问了lintel，要在u-boot的httpd恢复模式刷新。

tangxin991

就是在刷不死的uboot刷新的，通电按reset进去刷的，不是这样吗？

wlmwwx

是这样操作的，我的没问题，能工作。

gggompgf

原厂固件里提取出来的wifi-eeprom

神马教主

flash  内存换什么型号的？还有原厂内存和flash各是多少的？

神马教主

等有完美固件，帮我们兄弟做份详细点的

wlmwwx

神马教主 发表于 2013-5-18 18:10
flash  内存换什么型号的？还有原厂内存和flash各是多少的？

flash w25q64
DRAM hy561216221hp-d43      
原厂的flash 2MB，内存16MB