华硕RT-N16的配置真是令人流口水（上内部图）

空虚***

BCM4716的CPU，主频高达480M，可以超频至533M
32M的Flash
128M的DDR2内存
支持高达30W的并发数
带2个USB2.0接口
官方的固件就可以ipkg安装oleg的软件包，完全不需要刷DD之类的东东
这种配置别说嵌入式Linux了，就连windows都能跑了

看了一下淘宝，最低售价都是近1300

性能令人垂涎，价格却令人汗颜

以下可以点击看大图

1. # cat /proc/cpuinfo
   
2. 
   
3. 
   
4. system type             : Broadcom BCM4716 chip rev 1
   
5. processor               : 0
   
6. cpu model               : MIPS 74K V4.0
   
7. BogoMIPS                : 238.59
   
8. wait instruction        : no
   
9. microsecond timers      : yes
   
10. tlb_entries             : 64
    
11. extra interrupt vector  : no
    
12. hardware watchpoint     : yes
    
13. ASEs implemented        : mips16 dsp
    
14. VCED exceptions         : not available
    
15. VCEI exceptions         : not available
    
16. 
    
17. unaligned_instructions  : 2
    
18. dcache hits             : 2147483648
    
19. dcache misses           : 3488175871
    
20. icache hits             : 2147483648
    
21. icache misses           : 3735769009
    
22. instructions            : 2147483648

复制代码

1. # cat /proc/meminfo
   
2. 
   
3. 
   
4. MemTotal:       126336 kB
   
5. MemFree:        103188 kB
   
6. Buffers:          3872 kB
   
7. Cached:           7972 kB
   
8. SwapCached:          0 kB
   
9. Active:           4024 kB
   
10. Inactive:         9552 kB
    
11. SwapTotal:           0 kB
    
12. SwapFree:            0 kB
    
13. Dirty:               0 kB
    
14. Writeback:           0 kB
    
15. AnonPages:        1740 kB
    
16. Mapped:           1552 kB
    
17. Slab:             4672 kB
    
18. SReclaimable:     1152 kB
    
19. SUnreclaim:       3520 kB
    
20. PageTables:        360 kB
    
21. NFS_Unstable:        0 kB
    
22. Bounce:              0 kB
    
23. CommitLimit:     63168 kB
    
24. Committed_AS:     4284 kB
    
25. VmallocTotal:   786388 kB
    
26. VmallocUsed:      3972 kB
    
27. VmallocChunk:   781400 kB

复制代码

1. # dmesg
   
2. 
   
3. 
   
4. Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.1.2) #153 Tue Jun 23 16:25:53 CST 2009
   
5. CPU revision is: 00019740
   
6. Determined physical RAM map:
   
7. memory: 07fff000 @ 00000000 (usable)
   
8. On node 0 totalpages: 32767
   
9.   Normal zone: 255 pages used for memmap
   
10.   Normal zone: 0 pages reserved
    
11.   Normal zone: 32512 pages, LIFO batch:7
    
12. Built 1 zonelists.  Total pages: 32512
    
13. Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
    
14. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
    
15. Primary data cache 32kB, 4-way, linesize 32 bytes.
    
16. Synthesized TLB refill handler (20 instructions).
    
17. Synthesized TLB load handler fastpath (32 instructions).
    
18. Synthesized TLB store handler fastpath (32 instructions).
    
19. Synthesized TLB modify handler fastpath (31 instructions).
    
20. PID hash table entries: 512 (order: 9, 2048 bytes)
    
21. CPU: BCM4716 rev 1 at 480 MHz
    
22. Using 240.000 MHz high precision timer.
    
23. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    
24. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    
25. Memory: 126064k/131068k available (2771k kernel code, 4856k reserved, 564k data, 124k init, 0k highmem)
    
26. Calibrating delay loop... 238.59 BogoMIPS (lpj=119296)
    
27. Mount-cache hash table entries: 512
    
28. NET: Registered protocol family 16
    
29. PCI: Using membase 8000000
    
30. PCI: Initializing host
    
31. PCI: Reset RC
    
32. PCI: Fixing up bus 0
    
33. PCI: Fixing up bridge
    
34. PCI: Setting latency timer of device 0000:01:00.0 to 64
    
35. PCI: Fixing up bridge
    
36. PCI: Setting latency timer of device 0000:01:00.1 to 64
    
37. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
    
38. PCI: Fixing up bus 1
    
39. Time: MIPS clocksource has been installed.
    
40. NET: Registered protocol family 2
    
41. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
42. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
    
43. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
    
44. TCP: Hash tables configured (established 4096 bind 4096)
    
45. TCP reno registered
    
46. VFS: Disk quotas dquot_6.5.1
    
47. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    
48. squashfs: version 3.4 (2008/08/26) Phillip Lougher
    
49. NTFS driver 2.1.28 [Flags: R/O].
    
50. fuse init (API version 7.8)
    
51. io scheduler noop registered (default)
    
52. HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
    
53. N_HDLC line discipline registered.
    
54. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
    
55. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
    
56. loop: module loaded
    
57. PPP generic driver version 2.4.2
    
58. PPP Deflate Compression module registered
    
59. PPP BSD Compression module registered
    
60. PPP MPPE Compression module registered
    
61. NET: Registered protocol family 24
    
62. PPPoL2TP kernel driver, V0.17
    
63. PPTP driver version 0.8.2
    
64. Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
    
65. Amd/Fujitsu Extended Query Table at 0x0040
    
66. Physically mapped flash: CFI does not contain boot bank location. Assuming top.
    
67. number of CFI chips: 1
    
68. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    
69. Flash device: 0x2000000 at 0x1c000000
    
70. Physically mapped flash: squashfs filesystem found at block 1816
    
71. Creating 4 MTD partitions on "Physically mapped flash":
    
72. 0x00000000-0x00040000 : "boot"
    
73. 0x00040000-0x01fe0000 : "linux"
    
74. 0x001c63f8-0x01fe0000 : "rootfs"
    
75. 0x01fe0000-0x02000000 : "nvram"
    
76. Found a 0MB  serial flash
    
77. sflash: found no supported devices
    
78. GACT probability NOT on
    
79. Mirror/redirect action on
    
80. netem: version 1.2
    
81. u32 classifier
    
82.     Performance counters on
    
83.     input device check on
    
84.     Actions configured
    
85. Netfilter messages via NETLINK v0.30.
    
86. nf_conntrack version 0.5.0 (1023 buckets, 8184 max)
    
87. ctnetlink v0.93: registering with nfnetlink.
    
88. ipt_time loading
    
89. IPv4 over IPv4 tunneling driver
    
90. GRE over IPv4 tunneling driver
    
91. ipgre init: can't add protocol
    
92. ip_tables: (C) 2000-2006 Netfilter Core Team
    
93. TCP cubic registered
    
94. NET: Registered protocol family 1
    
95. NET: Registered protocol family 10
    
96. IPv6 over IPv4 tunneling driver
    
97. NET: Registered protocol family 17
    
98. Ebtables v2.0 registered
    
99. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    
100. All bugs added by David S. Miller <davem@redhat.com>
     
101. VFS: Mounted root (squashfs filesystem) readonly.
     
102. Freeing unused kernel memory: 124k freed
     
103. Warning: unable to open an initial console.
     
104. emf: module license 'unspecified' taints kernel.
     
105. PCI: Setting latency timer of device 0000:00:02.0 to 64
     
106. eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.27
     
107. PCI: Setting latency timer of device 0000:00:01.0 to 64
     
108. eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.27
     
109. Algorithmics/MIPS FPU Emulator v1.5
     
110. vlan1: add 33:33:00:00:00:01 mcast address to master interface
     
111. vlan1: add 01:00:5e:00:00:01 mcast address to master interface
     
112. vlan1: add 33:33:ff:2c:8b:9c mcast address to master interface
     
113. vlan1: dev_set_promiscuity(master, 1)
     
114. device eth0 entered promiscuous mode
     
115. device vlan1 entered promiscuous mode
     
116. device eth1 entered promiscuous mode
     
117. br0: port 2(eth1) entering learning state
     
118. br0: port 1(vlan1) entering learning state
     
119. br0: topology change detected, propagating
     
120. br0: port 2(eth1) entering forwarding state
     
121. br0: topology change detected, propagating
     
122. br0: port 1(vlan1) entering forwarding state
     
123. dbg: usb init
     
124. usbcore: registered new interface driver usbfs
     
125. usbcore: registered new interface driver hub
     
126. usbcore: registered new device driver usb
     
127. USB20H mdio control register : 0x80000018
     
128. PCI: Setting latency timer of device 0000:00:04.1 to 64
     
129. ehci_hcd 0000:00:04.1: EHCI Host Controller
     
130. ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
     
131. ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
     
132. ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
     
133. usb usb1: configuration #1 chosen from 1 choice
     
134. hub 1-0:1.0: USB hub found
     
135. hub 1-0:1.0: 2 ports detected
     
136. ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
     
137. USB20H mdio control register : 0x80000018
     
138. PCI: Setting latency timer of device 0000:00:04.0 to 64
     
139. ohci_hcd 0000:00:04.0: OHCI Host Controller
     
140. ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
     
141. ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
     
142. usb usb2: configuration #1 chosen from 1 choice
     
143. hub 2-0:1.0: USB hub found
     
144. hub 2-0:1.0: 2 ports detected
     
145. ufsd: no version for "struct_module" found: kernel tainted.
     
146. ufsd: driver loaded at c024d000 built on Mar  5 2009 13:51:35
     
147. UFSD version 7.02 (Mar  5 2009, 13:50:00)
     
148. NTFS read/write support included
     
149. $Id: ufsdvfs.c,v 1.195 2009/02/02 15:38:06 shura Exp $
     
150. usbcore: registered new interface driver usblp
     
151. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
     
152. SCSI subsystem initialized
     
153. Initializing USB Mass Storage driver...
     
154. usbcore: registered new interface driver usb-storage
     
155. USB Mass Storage support registered.
     
156. vlan1: del 33:33:ff:2c:8b:9c mcast address from vlan interface
     
157. vlan1: del 33:33:ff:2c:8b:9c mcast address from master interface
     
158. vlan1: del 01:00:5e:00:00:01 mcast address from vlan interface
     
159. vlan1: del 01:00:5e:00:00:01 mcast address from master interface
     
160. vlan1: del 33:33:00:00:00:01 mcast address from vlan interface
     
161. vlan1: del 33:33:00:00:00:01 mcast address from master interface
     
162. br0: port 1(vlan1) entering disabled state
     
163. vlan1: dev_set_promiscuity(master, 1)
     
164. vlan1: add 01:00:5e:00:00:01 mcast address to master interface
     
165. vlan1: add 33:33:00:00:00:01 mcast address to master interface
     
166. vlan1: add 33:33:ff:2c:8b:9c mcast address to master interface
     
167. br0: port 1(vlan1) entering learning state
     
168. br0: topology change detected, propagating
     
169. br0: port 1(vlan1) entering forwarding state
     
170. [k] track_flag=0, clean_flag=101, ipaddr=0
     
171. eth1: no IPv6 routers present
     
172. [k] track_flag=0, clean_flag=100, ipaddr=0
     
173. br0: no IPv6 routers present
     
174. httpd uses obsolete (PF_INET,SOCK_PACKET)
     
175. vlan1: no IPv6 routers present
     
176. eth0: no IPv6 routers present

复制代码

以上资料转自数位天堂和http://wl500g.info/

chil***

不知道华硕的定位，有这种性能需求的肯定会上小强跑ROS

wl1***

华硕有点有病，估计是那种公包不上市的产品。不过倒是挺诱人的。LZ有连接吗？

sing***

WRT-600N新的不也是一千多吗？走点裸板回来就好了～

mye***

不爱华硕这牌子, 二选一我还是喜欢WNR3500L

希望Linksys和Netgear发力

空虚***

只选对的，不选贵的

8230的性价比让我抛弃wrt54g家族

zxd***

这是个好东西啊，什么时候买一台

i***

牛比的嘛，5311散热片都不要的啊

空虚***

ink，弄点裸板来卖卖，呵呵

hh***

超级无线路由器？

zcqin***

我明明看的是BCM4718的CPU！楼主咋说是BCM4716啊！是我看错了吗？太贵了一般国人玩不起。

吸***

楼主引用的图上是4718，文字上却是4716，频率也只有二说啊，是238.59MHz还是480MHz啊

ruck***

这个NB···确实不错···

空虚***

对于4718的cpu，cpuinfo里面显示4716
而对于真正的4716，cpuinfo里面显示47116

sing***

啥都不想了，就等ink搞点裸板回来给我们折腾